Combination eye/face wash and shower safety stations feature a stainless steel or plastic bowl with two large FS-Plus™ spray-type outlet heads that deliver a flood of water for rinsing eyes and face. 

Combination eyewash and shower safety stations feature a Stainless Steel or plastic bowl with two GS-Plus™ spray-type outlet heads that deliver a flood of water for rinsing eyes.

Click on each individual item below for specific details about each model.

The Flush-Mounted Horizontal Drench Shower has a 12-7/8�-diameter flanged stainless steel showerhead which mounts evenly with a ceiling to conceal piping and fittings. The shower is quickly and easily activated with a stainless steel pull rod with a large triangular handle. The galvanized steel piping is protected by BRADTECT safety yellow coating. The shower features a chrome-plated brass 1� IPS stay-open ball valve and exceeds minimum water flow of 20 gpm at 30psi. TheBarrier-Free model is designed to comply with all ADA (Americans with Disabilities Act) guidelines regarding reaches, clearances and operating procedures. Complies with ANSI Z358.1-2004.
Note: The Drench Shower is designed for standard 8™-high ceilings. Please call customer service for special ordering information when using with other ceiling heights.

• Application: Thermostatic mixing valve to blend hot and cold water to deliver tepid water. Valve has flow capacity of 50 gallons (189 liters) per minute at 30 PSI (2.1 bar) pressure drop. Valve can be used to supply emergency shower or combination safety station. Depending on water supply size and pressure, valve can supply multiple units.
• Mounting: Valve inlets can be positioned on top, back or bottom of valve. Outlet can be on top or bottom. Valve can be configured in the field for any mounting position. Furnished with heavy duty stainless steel mounting bracket.
• Temperature Control: Valve has precision thermal actuator that senses incoming water temperature and automatically blends water to preset temperature. Valve is factory set to deliver 85°F (29°C) water. Temperature of tepid water can be adjusted as required and then locked. Furnished with dial temperature gauge as standard to monitor temperature of tepid water.
• Cold Water Bypass: If the supply of hot water is restricted or interrupted, an internal bypass allows the valve to deliver cold water only. In bypass mode, the valve delivers 38 GPM (144 L/min) at 30 PSI (2.1 bar) pressure drop.
• Hot Water Shutoff: Valve has internal PTFE valve seat. If the supply of cold water is interrupted, the valve will close completely and not deliver any water at all, eliminating any possibility of scalding.
• Flow Capacity: Refer to table below for flow capacity of valve at specified pressure drops.
• Checkstops/Filters: Each inlet has a lockable shutoff valve for maintenance, internal check valve to prevent backflow and stainless steel basket filter to remove debris from the water flow.
• Construction: Valve meets the requirements of the U.S. Safe Drinking Water Act as lead-free.
• Inlet/Outlet: 1” NPT female inlets and 1-1/4” NPT female outlet as standard.
• Quality Assurance: Valve is ASSE certified under ANSI/ASSE 1071. Valve is fully assembled and factory tested prior to shipment.

WATER PRESSURE/TEMPERATURE REQUIREMENTS

• Supply Pressure: Maximum incoming water pressure is 125 PSI (8.6 bar). Pressure of hot and cold water supplies can vary up to 25% and still deliver the flow and temperature required by ANSI/ASSE 1071.
• Hot Water Supply Temperature: Incoming hot water temperature range is 120° - 180°F (49° - 82°C). Guardian recommends that the hot water temperature not exceed 140°F (60°C).
• Cold Water Supply Temperature: Incoming cold water temperature range is 40° - 70°F (4° - 21°C). Cold water temperature must be at least 10°F (5.6°C) less than the temperature of the delivered tepid water.
• Tepid Water Temperature: Temperature of tepid water is adjustable within a range of 65° - 95°F (18° - 35°C) and then locks in position. High temperature limit stop is set at 90°F (32°C) to prevent misadjustment.

• Application: Combo eyewash and shower safety station. Unit is furnished with a temperature-actuated scald protection valve. When water temperature rises above 95°F, valve automatically opens to allow water to circulate through unit, preventing injury to user. Unit is designed so that, when drain valve is open, there are no “dead legs” of water standing in unit. Water flow stops when temperature falls below 95°F.
• Shower Head: 10" diameter orange ABS plastic with 20 GPM flow control.
• Shower Valve: 1" IPS chrome plated brass stay-open ball valve. Valve is US-made with chrome plated brass ball and PTFE seals. Furnished with stainless steel actuating arm and 29" stainless steel pull rod.
• Spray Head Assembly: Two GS-Plus™ spray heads. Each head has a “flip top” dust cover, internal flow control and filter to remove impurities from water flow.
• Eyewash Bowl: 11-1/8" diameter stainless steel.
• Eyewash Valve: 1/2" IPS chrome plated brass three-way self-draining stay-open ball valve. Valve is US-made with chrome plated brass ball and PTFE seals. After eyewash is used, valve permits water in spray head assembly to drain out.
• Pipe And Fittings: Schedule 40 galvanized steel. Furnished with orange polyethylene pipe covers for high visibility and corrosion resistance.
• Supply: 1-1/4" NPT female top inlet.
• Waste: 1-1/4" NPT female outlet. Outlet can be positioned at either 9-1/4" or 15-3/4" above finished floor by reversing lower pipe nipples.
• Sign: ANSI-compliant identification sign.
• Guardian Quality Assurance: Valve and spray head assemblies are factory assembled and water tested prior to shipment.

Cabinet-Mount Eye/Face Wash, Ea

Wall-Mounted Eye/Face Wash, Ea

Dual-Check Backflow Preventer, 3/8" IPS Female, Ea

Swing-Over Eye/Face Wash, Ea

Bradley 75S45-122 1/2" Diamond Rubber Ball Valve

Replacement float-off dust covers (package of 2).

• Application: Eyewash with stainless steel bowl for wall mounting. Two GS-Plus™ spray-type outlet heads deliver a flood of water for rinsing eyes.
• Spray Head Assembly: Two GS-Plus™ spray heads. Each head has a “flip top” dust cover, internal flow control and filter to remove impurities from the water flow.
• Valve: 1/2" IPS chrome plated brass stay-open ball valve. Valve is US-made with chrome plated brass ball and PTFE seals.
• Bowl: 11-1/8" diameter stainless steel.
• Mounting: Heavy duty cast aluminum wall bracket with corrosion resistant powder coated finish.
• Supply: 1/2" NPT female inlet.
• Waste: 1-1/4" NPT female outlet.
• Sign: ANSI-compliant identification sign.
• Quality Assurance: Unit is completely assembled and water tested prior to shipment.

• Application: All-stainless steel emergency shower for horizontal mounting. Ideal for use in areas where highly corrosive materials are handled, as well as in laboratory and clean room applications.
• Shower Head: 10" diameter stainless steel with 20 GPM flow control.
• Valve: 1" IPS stainless steel stay-open ball valve. Valve has stainless steel ball and PTFE seals. Furnished with stainless steel actuating arm and 29" stainless steel pull rod.
• Pipe And Fittings: Schedule 40 stainless steel.
• Supply: 1" NPT female inlet.
• Sign: ANSI-compliant identification sign.